Author Topic: Update Control System  (Read 4889 times)

0 Members and 1 Guest are viewing this topic.

Offline [NL] Terence van Acquoij

  • Newbie
  • *
  • Posts: 24
Re: Update Control System
« Reply #30 on: January 08, 2013, 12:39:29 PM »
Hello Train familie,

The Netherlands have made the Control System with Belgium. The Dutch team is almost ready with the programm. if we get a singnal from Belgiums RF system then opens the powerpoint. we have already made this test. Before St.Pölten we meeting with Belguim for the RF coupling. so we are almost done with this part.

Here is the link for you of our test:

http://www.youtube.com/watch?v=dRQuOKrvsMY


Greetzz,

The NL-Team

Offline [DE] Heinz Wildgrube

  • CNC-Network Coordinator
  • Administrator
  • Full Member
  • *****
  • Posts: 213
  • BBS TGHS Bad Kreuznach (Germany)
    • http://www.cnc-network.eu
Re: Update Control System
« Reply #31 on: January 11, 2013, 11:35:09 PM »
Dear Control System Group,

Wow, this solution looks very good  :D :) :D

Congratulations -
and thanks a lot for your work!

Many greetings
--
Heinz Wildgrube
CNC Network Coordinator
BBS TGHS Bad Kreuznach
Germany

News at:
http://www.cnc-network.eu

Offline [IT] Michele Agati

  • Newbie
  • *
  • Posts: 30
Re: Update Control System
« Reply #32 on: January 15, 2013, 03:57:21 PM »
Hello Terence,
your team has done a very good job!! 8)

I think that in St Polten, for the Control System Group, will be a very successful meeting!! ;)

I have only a question about the devices to put on the wagon.  Do you have a picture with the dimension of the latest (or finally) version?

Thanks a lot

Michele [IT]

Offline [NL] Terence van Acquoij

  • Newbie
  • *
  • Posts: 24
Re: Update Control System
« Reply #33 on: January 15, 2013, 04:25:14 PM »
Hello Michele,

Friday we are going to Belgium to couple the systems. then we know what the dimensions are. So I or my other team mates will post it friday;)

Your welcome. We will see you in ST.Pölten!

Terence [NL] & Team NL!

Offline [HR] Dominik Grdanjski

  • Newbie
  • *
  • Posts: 9
Re: Update Control System
« Reply #34 on: January 18, 2013, 10:51:55 AM »
Will we have electrical engineers (teachers) in St Polten ?




Offline [NL] Terence van Acquoij

  • Newbie
  • *
  • Posts: 24
Re: Update Control System
« Reply #35 on: January 18, 2013, 07:39:01 PM »
Hey Familie,

Our visit in Belgium was very succefull!!, our coupling works good. we will finish it in St.Pölten. 
Michele Agati, next week we will tell you the dimentions.  but it will be small ;)

Will we have electrical engineers (teachers) in St Polten ?

Not from our side.. but we can do it alone.


Thnx, and we will keep you updated.

Greetzz,

The NL-Team


« Last Edit: January 19, 2013, 01:36:24 PM by [NL] Terence van Acquoij »

Offline [HR] Dominik Grdanjski

  • Newbie
  • *
  • Posts: 9
Re: Update Control System
« Reply #36 on: January 20, 2013, 04:11:05 PM »
OK :)

Maybe we could have some electrical teachers on Skype, If we get stuck somewhere :) hehe

Offline [NL] Terence van Acquoij

  • Newbie
  • *
  • Posts: 24
Re: Update Control System
« Reply #37 on: March 18, 2013, 01:32:37 PM »
Hello familie!,

Were doing well at the control system!. The Belgium guys visited us and we are almost ready for assamble the components.
29 of March we are going to assamble the system. we have finished the piece for in the WAGON. So if you have any questions; ask us!

Greetz,

The Belgium and NL team!

Offline [AT STP] Friedrich Wilhelm

  • Newbie
  • *
  • Posts: 28
Re: Update Control System
« Reply #38 on: March 19, 2013, 11:29:07 AM »
Hi

Looks good. Finally, just for safety: You have two connections (i.e. solder pads) for our special electronics on the wagon just to switch it on (like a switch, with no power supply for our gimmicks)?

regards
Fritz

Offline [NL] Marc van Erp

  • Newbie
  • *
  • Posts: 25
Re: Update Control System
« Reply #39 on: March 19, 2013, 01:36:24 PM »
Hey Friedrich,

If they are finished we have one battery of 9v. This battery is only for the control system. Then each country has to bring there own battery and can put him into our print. From the other connector there comes 2 cables to the electronic gimmiks (plus and minus) for the country. If you push the button on the puzzlepiece the print will give a puls and the power of the battery will do it for 30 seconds.

I hope you can understand it.

Regards,

Control system group

Offline [AT STP] Friedrich Wilhelm

  • Newbie
  • *
  • Posts: 28
Re: Update Control System
« Reply #40 on: March 19, 2013, 02:47:10 PM »
OK, perfect. We have our gimmicks powered with 6V (4x AAA) and LEDs. So I will put wires to the battery holder, and to the LEDs too, of course. You will get 4 wires from our gimmick. Are you satisfied with me?

regards
Fritz

Offline [NL] Marc van Erp

  • Newbie
  • *
  • Posts: 25
Re: Update Control System
« Reply #41 on: March 19, 2013, 02:51:26 PM »
Hee,

Yes that is allright then we can connect them.

regards,

Control system group

Offline [HDH] Manuel Dentgen

  • Newbie
  • *
  • Posts: 5
Re: Update Control System
« Reply #42 on: March 19, 2013, 06:24:04 PM »
@ Friedrich and everyone who do not not yet know how to connect the wires:
I hope you have seen this: http://www.cnc-network.eu/forum/index.php?topic=517.0 ?
If not check it out. It should answer your questions.

@ NL/BE-Team:
Great Job  :D!

Offline [AT STP] Friedrich Wilhelm

  • Newbie
  • *
  • Posts: 28
Re: Update Control System
« Reply #43 on: March 20, 2013, 02:22:11 PM »
OK, thanks. I have missed this thread, sorry.

regards
Fritz