Author Topic: Puzzle piece finished  (Read 3022 times)

0 Members and 1 Guest are viewing this topic.

Offline [AT STP] David Burisch

  • Newbie
  • *
  • Posts: 2
Puzzle piece finished
« on: October 05, 2012, 09:55:31 AM »
Here is the finished puzzle piece. Please produce it until STP. greetings from Austria!

Offline [DE] Heinz Wildgrube

  • CNC-Network Coordinator
  • Administrator
  • Full Member
  • *****
  • Posts: 213
  • BBS TGHS Bad Kreuznach (Germany)
    • http://www.cnc-network.eu
Re: Puzzle piece finished
« Reply #1 on: October 08, 2012, 08:01:47 PM »
Hello,

Please don't forget to publish this drawings also as pdf file ;-)

Thanks a lot!

Many greetings
--
Heinz Wildgrube
CNC Network Coordinator
BBS TGHS Bad Kreuznach
Germany

News at:
http://www.cnc-network.eu

Offline [AT STP] Friedrich Wilhelm

  • Newbie
  • *
  • Posts: 28
Re: Puzzle piece finished
« Reply #2 on: October 18, 2012, 12:00:43 PM »
Hi

Here is the correct drawing. Unfortunately I had to change the dimension for the switch. Before ordering, in the specifications was written M12, but when I got the switch and tried to fix it, I have seen that it is M12x1. I hope, that nobody has finished his puzzlepiece at this moment with the wrong dimension.

Let the sun shine
Friedrich

Offline [HR] Gordana Eric

  • Newbie
  • *
  • Posts: 16
Re: Puzzle piece finished
« Reply #3 on: October 21, 2012, 12:50:52 AM »
Hello Friedrich and panel group,

Could you please tell me which is the depth of engraving and thickness of letters and country shape (ie tool diameter). Or it is not important?

Thank you!

Goga
Goga

Offline [DE] Heinz Wildgrube

  • CNC-Network Coordinator
  • Administrator
  • Full Member
  • *****
  • Posts: 213
  • BBS TGHS Bad Kreuznach (Germany)
    • http://www.cnc-network.eu
Re: Puzzle piece finished
« Reply #4 on: October 21, 2012, 12:25:41 PM »
Hello Goga,
Hello Panel Group,

As far as I remember there is something written in the minute like this:

  • "The details of the engraving were discussed and these will appear on the forum."
  • "The slot will be put at the back of each piece, as well as the engravings."
  • "The national code will consist of three letters, like in sport" ... "(three letters)."
  • "Position of the national code: top left corner, 10 mm Arial, 15 mm from the left edge, 10 mm from the top edge (centre)."
  • "The milling cutter to be used is a Diameter 2 mm Ballmill and the depth of cut is to be 0.4mm. Suggested Speed/Feed is 6000RPM/200mm per min."

Please feel free to have a closer look to thew minute. You will find it in the document section of our project web.

Nevertheless, I'm not sure, if all the details mentioned above are the final decisions!
Maybe someone of the panel group is able to confirm this to us?


Thanks a lot!

Many greetings
--
Heinz Wildgrube
CNC Network Coordinator
BBS TGHS Bad Kreuznach
Germany

News at:
http://www.cnc-network.eu
« Last Edit: October 21, 2012, 12:36:19 PM by [DE] Heinz Wildgrube »

Offline [AT STP] Friedrich Wilhelm

  • Newbie
  • *
  • Posts: 28
Re: Puzzle piece finished
« Reply #5 on: October 29, 2012, 02:05:22 PM »
Hi to all

For the letters you have the same tool and measurements as for the shape. The font Arial is standard, not bold, italic or anything else.
For the slot you need a 4mm square end mill like John asked me.

Please make a little connection between the slot and the M12 thread. It don't has to be large, we need it only for two small wires. This wires are coming from the LED-stripe and we will put it through the same hole as the wires from the switch.

Hey, when I look out of my window, I see snow!

greetings
Friedrich

Offline [NL] Kevin Vogels

  • Newbie
  • *
  • Posts: 11
Re: Puzzle piece finished
« Reply #6 on: October 29, 2012, 02:56:16 PM »
Dear people of the puzzel piece,

We need to know the exact details of the puzzel by next frighday so i ask you to pleas hurry and make the final decisions.

Yours,

Kevin Vogels [NL]

Offline [IE] John O Neill

  • Jr. Member
  • **
  • Posts: 54
Re: Puzzle piece finished
« Reply #7 on: November 06, 2012, 10:53:04 PM »
Hi all

We still need to specify the detail for the channel to take the wires.
At the moment these LED strips are being built and when one is finished this detail will be known.
So please be patient for a few more days until the detail is clear.
As soon as it is, a final design will be posted here.

Thank you for your patience

John

Offline [AT STP] Friedrich Wilhelm

  • Newbie
  • *
  • Posts: 28
Re: Puzzle piece finished
« Reply #8 on: November 19, 2012, 02:29:15 PM »
Hi

Thank you for waiting. We need a little connection for the wires of the LED-stripe like on my drawing (only detail, the rest is on the other drawings). The middle has to be 12mm from the side, and the minimum width is 2mm. But I  think, it will be easier to make it 4mm, for this size you have to mill for the slot of the LED-stripe too so it is still in the machine. This little slot has to be 5mm deep.
I have also added some pics of this. I hope, now is everything ready for producing.

kind regards
Fritz
« Last Edit: November 19, 2012, 02:31:25 PM by [AT STP] Friedrich Wilhelm »

Offline [IE] John O Neill

  • Jr. Member
  • **
  • Posts: 54
Re: Puzzle piece finished
« Reply #9 on: November 19, 2012, 07:09:04 PM »
Hi Fritz and Train Family

Thanks to Fritz for the details of the Puzzle Piece.
One comment and two questions:
Viewed from the front the switch seems to encroach on the slot.
This looks a little bit strange, but on the plus side it will hide the wire slot.
Q1. Do the switch screws protrude (stick out) at the back of the puzzle piece?
The desk makers will need this information.
They will also need to know the size and position of the holes in the desk for the wires.
Q2. If we come to St. Polten with no M12x1 thread is there a tap for doing this on site?

Thanks,
John

Offline [DE] Heinz Wildgrube

  • CNC-Network Coordinator
  • Administrator
  • Full Member
  • *****
  • Posts: 213
  • BBS TGHS Bad Kreuznach (Germany)
    • http://www.cnc-network.eu
Re: Puzzle piece finished
« Reply #10 on: November 19, 2012, 11:37:47 PM »
Hello Fritz,

Looks good  :)

Could you please provide us with a complete drawings set of the new puzzle piece incl. the new slot as step, dxf and pdf file?

I know, it's work, but it's necessary for a complete documentation, because in 5 years nobody knows what we have done in this point.

We should learn from the mistakes we've done in the first Train Project, where we've lost a lot of important info in the meantime.

Thanks a lot!

Many greetings
--
Heinz Wildgrube
CNC Network Coordinator
BBS TGHS Bad Kreuznach
Germany

News at:
http://www.cnc-network.eu
« Last Edit: November 19, 2012, 11:43:13 PM by [DE] Heinz Wildgrube »

Offline [AT STP] Friedrich Wilhelm

  • Newbie
  • *
  • Posts: 28
Re: Puzzle piece finished
« Reply #11 on: November 26, 2012, 12:51:52 PM »
Hi John

The encroach is not really striking, it is very small and we have 25 pieces at all, viewed by different angles. On our desk there is so much other to see....

Yes, the switch sticks out a little on the back side, between 3 and 4mm. But it is no problem, the diameter of this part ist less then the 12mm. So, the desk makers have to drill holes with a diameter of 12mm, then we have space enough for the outsticking switch AND the wires too. You will not see the holes, because they are covered by the cellular rubber. And yes, we can cut the thread in our school, we have a lot of machines here and people who know how to work with them   8)

Hi Heinz

I will tell this to our students and my CNC-colleagues, because I don't know, what "step" is  ;)

kind regards
Fritz

Offline [IE] John O Neill

  • Jr. Member
  • **
  • Posts: 54
Re: Puzzle piece finished
« Reply #12 on: November 26, 2012, 08:56:40 PM »
Hi Panel and Desk group/Train Family

Great work Fritz

I have looked at the minutes and on the forum but cannot see any reference to the map size.
Do we need to set a square or rectangle size and position of the country outline?
Have a look at the jpeg below and say what you think.

Also the desk makers have more detail now but still not enough.
Can the depth of the desk be reduced to say 50mm instead of 100mm.
Anyone know the answer? Control group maybe?

Thanks
John

Offline [AT STP] Mike Fahrafellner

  • Newbie
  • *
  • Posts: 20
Re: Puzzle piece finished
« Reply #13 on: November 30, 2012, 11:57:41 AM »
This is the wrong file.
Please wait until monday. I hope we can avoid such mistakes in the futere.
Sorry!
Mike
« Last Edit: November 30, 2012, 03:23:06 PM by [AT STP] Mike Fahrafellner »

Offline [AT STP] Mike Fahrafellner

  • Newbie
  • *
  • Posts: 20
Re: Puzzle piece finished
« Reply #14 on: December 05, 2012, 09:37:09 AM »
here are the really finished drawings  ;)

Mike